What changes is not the musical content itself, but:
- The form of the digital signal entering the DAC
- The digital processing path used inside the DAC
- The Noise Shaping and filtering performed before digital-to-analog conversion
For some DACs, this may produce different final output characteristics compared with direct PCM input.
Why Convert PCM to DSD?
Most digital music files are PCM, for example:
- 44.1 kHz / 16-bit
- 96 kHz / 24-bit
- 192 kHz / 24-bit
A conventional playback path is usually:
What actually changes is the type of digital signal received by the DAC.
What Is the Difference Between PCM and DSD?
PCM
PCM describes each sample using a lower sample rate and multiple bits of precision.
For example, CD audio uses 44,100 samples / second and 16 bit / sample. High-resolution PCM may use 96 kHz / 24-bit or 192 kHz / 24-bit.
Each sample can represent many different amplitude levels.
DSD
DSD represents the signal using an extremely high sample rate and 1 bit.
Each individual sample has only two states, 0 and 1. Because the sampling speed is extremely high, variations in the density of 0s and 1s can represent the audio waveform.
- DSD64: 2.8224 MHz
- DSD128: 5.6448 MHz
- DSD256: 11.2896 MHz
The key to DSD is not that “1 bit is highly precise.” Instead, DSD combines a very high sampling frequency with Noise Shaping to preserve useful audio information within the audible band while pushing much of the quantization noise into the ultrasonic range.
The process generally has three stages.
1. High-Ratio Oversampling of PCM
For example:
The original PCM samples are not simply duplicated. An interpolation filter calculates new signal values between the original sample points.
2. Sigma-Delta Modulation
The high-sample-rate PCM enters a Sigma-Delta Modulator, which converts high-precision multi-bit PCM into a 1-bit DSD stream while controlling quantization error through feedback and Noise Shaping.
3. Push Quantization Noise Out of the Audible Band
1-bit quantization inherently generates substantial error. Sigma-Delta modulation uses Noise Shaping to move much of this quantization noise toward higher frequencies while keeping noise lower within the 20 Hz to 20 kHz audible band.
Therefore, DSD performance cannot be judged simply by “1 bit.” Important factors include:
- Oversampling ratio
- Modulator order
- Noise transfer function
- Stability
- Input headroom
- Ultrasonic noise control
Why Can This Affect Sound?
It is not:
What may change is how the downstream DAC processes the digital signal.
DACs Often Perform Similar Processing Internally
Many modern DACs do not directly convert incoming PCM values into analog voltage. A typical digital DAC may use a path such as:
In other words, even when the DAC receives PCM, it may internally convert the signal into another high-sample-rate, low-bit-depth stream before final conversion.
Why Can Player-Side Processing Matter?
With direct PCM input:
For some DACs, DSD input may bypass or alter part of the PCM digital processing path, depending on the DAC chip and manufacturer implementation.
DAC Architectures Can Differ Significantly
Sigma-Delta DAC
Very common in modern DACs. Their internal architecture often includes Oversampling, Digital Filters, Noise Shaping, and Sigma-Delta Modulation.
PCM and DSD inputs may use different front-end processing, while eventually reaching the same or a similar conversion core.
R-2R / Ladder DAC
R-2R DACs use resistor networks for digital-to-analog conversion. Their handling of DSD varies greatly between products.
Some process DSD natively or use a dedicated DSD conversion path. Others may first convert DSD to PCM / multi-bit before sending it into the ladder.
Therefore, “R-2R DAC + DSD” does not automatically mean fully native DSD. The actual implementation depends on the manufacturer.
FPGA / Discrete DAC
Some DACs use FPGA, CPLD, discrete conversion elements, custom digital filters, and custom Noise Shaping.
Why Can the Same Song Sound Different?
If a DAC uses different PCM and DSD input paths, the following may change:
- Digital filter
- Oversampling filter
- Modulator
- Interpolation strategy
- Ultrasonic noise spectrum
- Interaction with the analog output filter
Even when playing the same PCM source:
and:
may produce different final analog outputs.
The difference comes from changes in the digital processing chain and the DAC operating path, not because the source file has somehow gained additional information.
What Might Change Subjectively?
Differences between PCM and DSD output are not fixed and vary across DACs and systems. You may notice changes in:
- High-frequency texture
- Transient response
- Spatial presentation or sound density
- A softer or more continuous overall presentation
These changes depend on DAC architecture, DSD Modulator design, output stage, analog filtering, headphones or speakers, and the recording itself.
Why Is the Modulator Itself Important?
“Converted to DSD” does not mean every result is the same.
The design of the DSD Modulator directly affects:
- In-band audio noise
- Ultrasonic noise
- Stability
- Maximum safe input level
- Transient behavior
A simple modulator and a carefully controlled high-order modulator can produce significantly different output characteristics.
Input Headroom
A DSD Modulator generally cannot simply accept PCM signals close to 0 dBFS without restriction.
The purpose is not to change the loudness style, but to:
- Prevent Modulator overload
- Improve stability
- Reduce distortion
- Avoid abnormal output under high-level input
What Is the Difference Between DSD64, DSD128, and DSD256?
A higher DSD rate means a higher Oversampling ratio.
For the 44.1 kHz family:
- DSD64: 2.8224 MHz
- DSD128: 5.6448 MHz
- DSD256: 11.2896 MHz
Higher sampling rates can theoretically:
- Provide more frequency space for Noise Shaping
- Make it easier to move quantization noise away from the audible band
- Reduce in-band audio noise
But they also increase:
- CPU processing
- USB data throughput
- DAC workload
- Real-time modulation requirements
A higher DSD rate does not automatically sound better on every system. The DAC’s native support and actual implementation still matter.
Why Is an External DAC Required?
The built-in audio devices on iPhone, iPad, or Mac do not necessarily support DSD bitstreams.
A typical path is:
If the DAC does not support the target DSD rate, the system may need to:
- Use a lower DSD rate, such as DSD256 → DSD128
- Fall back to PCM output
What Is the Relationship Between DoP and DSD?
DoP stands for DSD over PCM.
It does not convert DSD audio back into PCM. Instead, it uses PCM-compatible frames to carry a DSD bitstream. When the DAC detects the marker, it recognizes that the payload contains DSD data.
Therefore, DoP is a transport method, not an audio conversion format.
This is also why DoP has strict requirements for DAC format negotiation, bit layout, and carrier sample rate.
Digital Headroom, High-rate Oversampling, and the DSD Modulator are all implemented by Mossca.
Mossca builds the playback path according to:
- Original PCM sample rate
- DAC capabilities
- Available DSD rate
- Output-device state
The maximum available DSD rate depends on the external DAC and the system connection.
It is particularly suitable for:
- Heavy external-DAC users
- Users who want the player to control Oversampling / Modulation
It may not be suitable for:
- Users relying only on built-in speakers
- Mobile scenarios where power consumption is important
- Users who want strict Bit-Perfect playback
Is It Bit-Perfect?
The system has already performed:
The digital data has changed.
Regular PCM Upsampling:
The output remains multi-bit PCM.
Both involve Oversampling, but the final data format and DAC input path are different.
A Simple Way to Understand It
With normal PCM playback, PCM is handed to the DAC, and the DAC decides how to perform Oversampling and modulation.
It is another digital playback-path choice, not simply a “format conversion.”
FAQ
Does it always sound better than PCM? No. The result depends on DAC architecture, the modulator, analog output stage, and the entire system.
Why do different DACs sound so different? Because different DACs process PCM and DSD internally in different ways. Some eventually use similar conversion paths, while others are substantially different.
Does it increase CPU usage and power consumption? Yes. High-ratio Oversampling and real-time DSD Modulation require continuous computation. Higher DSD rates generally require more processing and greater data bandwidth.
Can it be used together with EQ? Yes. The theoretical path can be: